Home>FILTRES>KIT REVISION>KIT 3 FILTRES ADAPTABLE LOMBARDINI FOCS ET PROGRESS AVEC CARTOUCHE GO. (except where indicated in this manual). • Stop the engine before Diesel engine: LOMBARDINI mod. LDW FOCS • Keep the diesel engine running . FOCS Workshop Manual_cod. _1° ed_ rev. CHAPTER INDEX – This manual contains pertinent information regarding the repair of LOMBARDINI .

Author: Zulugami Voodookinos
Country: Uganda
Language: English (Spanish)
Genre: Education
Published (Last): 5 October 2006
Pages: 243
PDF File Size: 10.12 Mb
ePub File Size: 19.48 Mb
ISBN: 514-3-47207-884-7
Downloads: 47463
Price: Free* [*Free Regsitration Required]
Uploader: Akinogul

In case it is different from zero, adjust the regulator block nuts to move it, lombarxini relation to the rod 3, in the direction that goes from the flywheel to the timing. Continue the periodical maintenance afterkm by starting from 7, km. Empty out completely the fuel tank. Test Head B Assembly To determine the piston clearance and, by consequence, which copper gaske is most suitable it is necessary to consider the A value of the piston that projects furthest.

LDW T – lombardini service. The cover contains part of the lubrication duct of the camshaft and of the lomhardini arms, as well as part of the engine vent system. Oil Pressure Check If so, it is important to inform and train them regarding the type of activity they will be performing in order to prevent risks to the health and safety of all persons involved. Then rotate the crankshaft until the TDC is read in the dial gauge.


Lombardini Diesel Engine Part Manual Ldw 1404

Injector, Setting old Type All tools must be in good working condition so that engine components are not damaged and that operations are carried out properly and safely.

If you only want to check the nozzle it is not necessary to balance the deliveries; provided that when you dismount the rod you do not loosen adjusting screws 1 and 2 fig. Overpressure valve opening pressure of 0. During remounting be careful with oil exhaust hose 4 that needs to be properly inserted into its housing on the cylinder head.


Check the length of the drive rod and ofcs it is not the right size, replace it. Crankcase Breather – Ldw To carry out the timing of the injection pumps and speed governor see page Do not route the welding lead over or near the wiring harnesses of the engine or plant.

See “Intake manifold — Remote air filter” on page 23 Figure 1.

The stroke H that the torque gearing device allows to be carried out by lever L, will increase the injection pump delivery and the torque will hit its maximum value. Service-Manual – Frank’s Hospital Workshop.

These lifting entretein are not suitable for the entire machine; in this case, the eyebolts installed by the manufacturer should be used. Diesel fuels that satisfy the following specifications are suitable for use in this engine: The test heads complete with pipes are supplied together with instrument ref. Camshaft Timing – Belt Tightening Tool Required Settings as Most Commonly Applies Pistons at the nominal diameter are only supplied in category A.


Cylinder head, removal Important Do not remove the cylinder head when hot to avoid deformation. Coolant High Temperature Lamp Sensor For the calibration of the E.

Remember me Forgot password? The spongy filtering material in oil-cooled air filters must not be soaked in oil. Do not allow the oil to come into contact with the skin.

Lombardini LDW Manuals

We share information about your activities on the site with our partners and Google partners: Via lever 1 of the tool, open the valve until it comes into contact with the piston. Explain the main result of this experiment and what physics you learned. Remove the wntretien, after having unscrewed central screw 1 and proceed with the four lateral screws.

Check the peripheral rubber sealing gasket and the two dustprotection rings of the two pulleys, if mounted.

Injector, Spark Arrester Rotate the crankshaft until the unit injector cam lobe 2 forces the cam follower 1 to the highest position, then insert a suitable sized hardened pin into the hole 3 and rotate the crankshaft until the cam follower 1 is at the lowest position.