KC778B DATASHEET PDF

COMedia KCB datasheet, Master PIR Control Chip (6-page), KCB datasheet, KCB pdf, KCB datasheet pdf, KCB pinouts. KCB Datasheet, KCB PDF, KCB Data sheet, KCB manual, KCB pdf, KCB, datenblatt, Electronics KCB, alldatasheet, free, datasheet. KCB datasheet, cross reference, circuit and application notes in pdf format.

Author: Mehn Kigataxe
Country: South Africa
Language: English (Spanish)
Genre: Politics
Published (Last): 26 May 2016
Pages: 229
PDF File Size: 16.73 Mb
ePub File Size: 3.69 Mb
ISBN: 988-3-70850-411-9
Downloads: 8724
Price: Free* [*Free Regsitration Required]
Uploader: Kikasa

I Daylight detector circuitry is designed to use either silicon photo diode or CdS detector. C High sensitivity PIR input with special noise cancellation circuitry. Kc778h High sensitivity PIR dataheet with special noise cancellation circuitry. M Four main operating modes can be used in any combination: Load turns off manually, with a momentary contact switch. Load turns on when motion is detected adjustable sensitivity. M Four main operating modes can be used in any combination: Due to its high sensitivity and reliability, it is also widely used in security product.

Adjustable OFF timer activates whenever motion stops. If the load goes off because you stopped moving reading a book for exampleyou have 6 datasueet to wave your arm to turn the load back on.

D Choice of two PIR gain settings: Auto-ON mode can be disabled.

The filter response can be measured in this way. Adjustable daylight detector disables Auto-ON during daytime. Due to its high sensitivity and. The value of the pot is not critical and any value between K Adjustable OFF timer accuracy is determined by external components.

  DEMAG AC 80-2 PDF

Pin 8 Pyro S is a sensitive node and the external interconnect to this pin should be made as short as. E Adjustable PIR sensitivity. Due to its high sensitivity and. A Circuit design maximizes performance while minimizing external component count and board layout space. B Low cost solution for PIR motion control switching applications. This dztasheet should also be closely surrounded by a ground plane. E Adjustable PIR sensitivity. The MPCC has been designed for easy implementation.

H High immunity to line frequency noise. Auto-ON mode can be disabled. If the load goes off because you stopped moving reading a book for exampleyou have 6 seconds to wave your arm datwsheet turn the load back on. Load turns off if there is no motion during the time delay. If Auto-ON mode is disabled, the load will turn on if there is motion within 6 seconds. J Adjustable daylight detector sensitivity. The output of the switched capacitor bandpass filter can be seen on pin 3 Offset Filter when the external.

A Circuit design maximizes performance while minimizing external component count and board layout space. Auto-OFF mode can be disabled. Daylight detector dafasheet be disabled. Auto-OFF mode can be disabled.

KCB datasheet & applicatoin notes – Datasheet Archive

H High immunity to line frequency noise. J Adjustable daylight detector sensitivity. The Sensitivity Adjust pot is used to select a voltage between the pyro drain reference voltage minimum sensitivity and Gnd maximum sensitivity. Adjustable OFF timer activates whenever motion stops. Load turns off if there is no motion during the time delay. B Low cost solution for PIR motion control switching applications. I Daylight detector circuitry is designed to use either silicon photo diode or CdS detector.

  ALONG THE WAY TGC PRASAD PDF

Ozitronics – Security

dataseet F Internal switched capacitor bandpass filter reduces external component count and improves reliability by. Load turns on when motion is detected adjustable sensitivity. If Auto-ON mode is disabled, the load will turn on if there is motion within 6 seconds. F Internal switched capacitor bandpass filter reduces external component count and improves reliability by minimizing sensitivity to external component values. Adjustable daylight detector disables Auto-ON during daytime.

K Adjustable OFF timer accuracy is determined by external components. Daylight detector can be disabled.

Pin 8 Pyro S is a sensitive node and the external interconnect to this pin should be made as short as possible. Due to its high sensitivity and reliability, it is also widely used in security product. If Auto-ON mode is disabled, the load will turn on if there is motion within 6 seconds after turn-off.

KC778B Datasheet PDF

D Choice of two PIR gain settings: The Sensitivity Adjust datasgeet is used to select a voltage between the pyro drain reference voltage minimum. Load turns on manually, with a momentary contact switch.

The MPCC has been designed for easy implementation.