JBL 2022H PDF

JBL H (8Ohm). Unavailable. Category of diameter 12 inch / cm; Znom 8 ohm; Weight volume is not set, then delivery by plane is not possible. Brand New JBL H 12″ Aftermarket Recone Kit, 8 ohm. Parts specifications: Cone: 12″ outside diameter, ″ deep, ″ voice coil opening; Voice. Subwoofer JBL H. General specifications: diameter 12 inches, maximum power W. Thiele-Small parameters: frequency of self resonance Fs=75 Hz, .

Author: Nit Zulukora
Country: Guinea
Language: English (Spanish)
Genre: Technology
Published (Last): 28 September 2018
Pages: 200
PDF File Size: 14.23 Mb
ePub File Size: 14.91 Mb
ISBN: 218-9-87312-550-2
Downloads: 17102
Price: Free* [*Free Regsitration Required]
Uploader: Dusida

The is also its own, it is an underhung design with a gap depth of 13mm. All times are GMT Read times Brian Elstro Jr.

JBL 2022H 12-inch speaker unit

I’ll leave the flame suit on for this February 24, Ie putting a kit in an E and so forth. Ditto E, E, and It has been quite a few years since I was doing reconing-but I remember that the magnet thickness was different between them. For a temporary fix I removed an older cone from another torched woofer, removed its suspension and dustcap, carefully removed the dustcap from the jbl and trimmed the glue from the cone as well as I could.

2022n what Tim recommended and give Charlie Tappa a call. It’s really a mid-range, a mid-bass at best. Logged If we knew what the hell we were doing, we wouldn’t call it research would we.

  JACQUES VALLEE PASSPORT TO MAGONIA PDF

From what I’ve been able to understand, is that the is JBL’s new king of midrange The letter suffix represents the impedance, not frequency range of the speaker. I thought the magnet slab was thicker. I was under the thought that the suffix was also something that showed intent or use of the driver eg- a single driver with a 16ohm impedance would be used for a total 3 or 4 way system impedance of 8 ohms, but a single 4 ohm driver would be used for a 2 way system impedance of 8 ohms The kit is the same cost as a H.

February 21, One starting point in my confusion I read that someone re-coned a to aincreasing x-maxx how I have compared these side by side and could not find any difference in the basket. 20022h the taper of the drivers was different I had to cut the new cone at an angle and push it to fit the taper.

However the magnet structures and magnetic energy focusing are different-so you will end up some sort of “half breed”. Logged Brian Elstro Jr. I think they both fall inbetween the mbl and “reproducer” sound The x came in 3 versions listed below.

The Marketplace for Musicians |

The time now is The rip went all the way around the dust cap which made me think that I had totally blown itand at one point into the middle of the cone. None were specifically for “mid range”.

  HGTG 11N120 PDF

Blew a in the monitor older mr series due to a broken handle overexcursion With proper processing do you think that it would be a good idea to just stick the in and work it out, jnl re-coning the February 18, Results 1 to 5 of 5. Differences were achieved in cone composition, coil windings, and VC former material.

The letter following the is used to designate the impedence. It sounds to me that you would prefer the ‘s over ‘s 22022h mid use.

Please update your browser to use Reverb

And for the recone price, I would keep the with it’s bigger 20222h and 4″ coil. If we knew what the hell we were doing, we wouldn’t call it research would we. Is it LF or MF and can it be reconed to a ? You will get an enormous reward. By that I mean the kits will interchange physically.

It beat itself so badly that part of the cone was actually soft to the touch, and very weak. I don’t know anything about the I guess you would call it JBL’s “midline” series driver. Another question, can the be reconed to the specs better LF handling?