FRONIUS TRANSPULS SYNERGIC 4000 MANUAL PDF

MIG/MAG Power source. TransSynergic Power Supply pdf manual download. Also for: Transsynergic , Transpuls synergic , Transpuls synergic. w . wwb. Fronius. U odyanina virusi wala 42,, . your TransSynergic / (TS /) and TransPuls Synergic . The instruction manual must be kept at the welding-machine location at all times. TRANSPULS SYNERGIC // source series from Fronius is a sensation of just this kind. sources for both manual welding and automated and .

Author: Dosida Mazujin
Country: Denmark
Language: English (Spanish)
Genre: Education
Published (Last): 6 January 2009
Pages: 272
PDF File Size: 17.83 Mb
ePub File Size: 7.47 Mb
ISBN: 137-1-33908-848-7
Downloads: 89281
Price: Free* [*Free Regsitration Required]
Uploader: Bam

Calibrating Push-pull Unit When lifting the drive unit 2do not pinch, bend or strain the cables. Cmt Advanced Welding Shielding gas Check shielding gas solenoid flowing out?

FRONIUS TRANSSYNERGIC SERVICE MANUAL Pdf Download.

Primary rectifier General remarks 400 following primary rectifiers are used: Function over- Varistors provide protection against momentary overvoltage of the mains view Capacitors and coils form an LC low-pass filter that moderates the parasitic fre- quencies over 60 Hz Capacitors divert disturbances to earth and also between the phases Resistors discharge the line filter capacitors Plug layout Fig.

Special 4-step Mode Page 20 – Nothing happens on control panel TPS Terms And Abbreviations A – C Obligations Of Personnel Transpuls Synergic Replacing The Strain-relief Device Shunt General remarks The shunt item number 43, is a current sensor which permits the isolated capture of the welding current. Cmt Automated Welding Inserting The Wirespool NT 60 – switched mode power supply 60 V The NT 60 switched mode power supply item number 4,,Z for the wire-feed General remarks unit motor.

  AKKP 1994 PDF

AC Power Distribution Transpulls Component position in the machine Secondary power module Fig. Work performed incorrectly can cause serious injury and damage. For connecting the power source to the serial interface on a PC, for: When putting the drive continued unit 2 in place, do not pinch, bend or strain the cables.

Fitting transfor- Push insulators 15 onto secondary 15 connections Wind both of the middle primary leads twice around the ferrite core and fasten with cable tie 14 15 14 Fig. Function overview Principle of the The machines are totally digitized, microprocessor-controlled inverter power sources.

Fronius TransSynergic 4000 Service Manual

Time Digital Control Panel At maximum wirefeed speed, the wire-feed unit motor does not deliver any drive units are actual rotational speed value. Function Overview Function over- Varistors provide protection against momentary overvoltage of the mains view Capacitors and coils form an LC low-pass filter that moderates the parasitic fre- quencies over 60 Hz Capacitors divert disturbances to earth and also between the phases Resistors discharge the line filter capacitors Plug layout Fig.

Every 6 Months Wire-stick Control Function Connecting The Mains Cable When fitting the control panel 7take care not to bend, stretch or strain the ribbon cable. TranssynergicTranspuls synergicTranspuls synergic Error codes St1 E 5 shown when the Cause: Table of contents Table Of Contents Function Overview Function overview Principle of the The machines are totally digitized, microprocessor-controlled inverter power sources.

Setting The Contact Pressure Function Overview Tools and This provides an overview and description of all equipment required for servicing the measuring power source professionally.

  AN ENDLESS SUMMER CJ DUGGAN PDF

In the course of replacement, the diodes must not be interchanged. When putting the drive unit aynergic in place, do not pinch, bend or strain the cables.

Function Tests Function tests General Under normal circumstances, function tests are only mandatory following repair work. Table of service Err code no. Entire Circuit Diagram Entire circuit diagram Storage location The circuit diagram is located inside the power source. Removing trans- Loosen 4 screws 7 for secondary 11 former transformer leads on copper sheet continued Loosen hexagon nut 8 using a size 13 spanner Remove protective element 9 and throttle lead 10 Loosen 4 screws 11 on the transfor- mer mxnual 12 10 Remove transformer holder Don’t show me this message again.

Tps Power Source Obligations Of The Operator To print the manual completely, please, download it.

Fronius TransPuls Synergic 4000 Manuals

The test voltage is V DC. The chip is integrated into the plastic housing and provided with a pluggable Molex connection. The actual data are measured machines continuously, and the machine responds immediately to any changes.

On the NF PC board, the mains voltage is on! Key Combinations – Special Functions The safety cut-out has tripped. Table of contents Foreword and safety instructions Design Of The Brake Visual inspections General The following must be visually inspected without any further dismantling of the system. Page Fitting transfor- continued 19 18 22 23 20 21 Fig.