FRENIC LIFT MANUAL PDF

FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Doshicage Fenriktilar
Country: Cyprus
Language: English (Spanish)
Genre: Love
Published (Last): 24 September 2013
Pages: 397
PDF File Size: 13.86 Mb
ePub File Size: 20.59 Mb
ISBN: 131-7-41918-945-1
Downloads: 89360
Price: Free* [*Free Regsitration Required]
Uploader: Bracage

Page 81 [ 24 ] Out of control speed Problem An out of control error PG failure occurs between the speed command and the speed feedback. To improve cooling efficiently, you can take the heat sink out of the equipment or the enclosure as shown on the right so that cooling is done both internally and externally this is called “external cooling”.

Doing so could cause fire. Push the front cover against the case of the inverter and slide it upward until the latch at its top engages with the case. Page 85 Table 7. Otherwise, the inverter may be broken if you turn the power ON. Lighten the load or change the inverter for an upper size. You need to replace the option card.

Last digit of year If you suspect the product is not working properly or if you have any questions about your product, contact your Fuji Electric representative. Read through this instruction manual and be manuxl with the handling procedure for correct use.

Page 37 Table 2. For the inverters with a capacity of 22 kW or below, wait at least 5 minutes; Select an inverter according to the applicable motor ratings listed in the lifg specifications table for the inverter. Precautions for use Driving a V When driving a V general-purpose motor with an inverter using ex- general-purpose tremely long wires, damage to the insulation of the motor may occur. Each part of the product has its own service life that will vary frsnic to the environmental and operating conditions.

  BAKI SHUNYA PDF

Maximum speed F03 2 The reference torque bias follows the input voltage level on terminal [12]. Page 49 An undervoltage or an alarm has been occurred. FRENIC-Lift is an inverter designed to drive a three-phase induction motor hereafter called an induction motor and a three-phase permanent magnet synchronous motor hereafter called a synchronous lifg for exclusively controlling elevating machinery.

If frenjc of these conditions has occurred, either eliminate the abnormal or error factor s manua perform tuning again, or contact your Fuji Electric representative. Tuning procedure What follows gives you a tuning procedure of the inverter for a motor using a multi-function keypad option.

Date of purchase Inquiries for example, point and extent of breakage, uncertainties, failure phenomena, and other circumstances Page For the braking resistor built-in type, refer to the next page.

Selecting function code data assigns the corresponding function to [X1] terminals [ X1] to [X8] as listed below.

Contact your Fuji Electric representative. U, V and W respectively and that the grounding wires are connected to the ground electrodes correctly. This chapter lists specifications including output ratings, control system, external dimensions and protective functions. For details, refer to [X2] Digital Chapter 5, Section 5. Chapter 4 Running The Motor U, V and W respectively and that the grounding wires are connected to the ground electrodes correctly.

Possible Causes What to Check and Suggested Measures 1 No power supplied to the Check the input voltage, output voltage and lkft voltage unbalance. Also remove the case fixing screws from the top. By pressing ‘print’ button you will print only current page.

FUJI ELECTRIC FRENIC-LIFT SERIES INSTRUCTION MANUAL Pdf Download.

Page In no event will Fuji Electric Co. Accident or injury may result.

  LARAVEL FROM APPRENTICE TO ARTISAN PDF

Trip with alarm after running for t he period specified by timer y03 2: Three-phase v series, three-phase v series, single-phase v series 6 pages. Each function code consists of a 3-letter string.

When the inverter is used to run a general-purpose motor, the temperature Torque characte- of the motor becomes higher than when it is operated using a commercial ristics mankal tem Enable data prot ection Note: Consult your Fuji Electric representative if these terminals are to be used. The case fixing screws are not necessary frnic external cooling. The 1st week of January is indicated as ’01’.

Page 18 1 Liftt all of the base fixing screws from the top and bottom of the inverter. Increase F26 Motor Sound Carrier frequency. Page 40 Table 2. Note 2 To protect wiring, insert a molded case circuit breaker MCCB or an earth leakage circuit breaker ELCB with overcurrent protection of the type recommended for the inverter between frenid commercial power supply and the inverter. In no event will Fuji Electric Co. Check that a mechanical brake is in effect.

Use them in accordance with your system requirements. Torque limit time 0.

Fuji Electric FRENIC-Lift series Instruction Manual

If any of the problems listed below occur, take an appropriate measure against them. Wiring For Control Circuit Terminals 2. Using the optional multi-function keypad allows you to start and manuual the motor, monitor running status, and switch to the menu mode.

Set up L02 for correct data. Disable Times Times 1 to Init ialize all function code data to t he factory defaults H04 Auto-resetting 0: