CHORD DSP8000R PDF

Préampli-Processeur CHORD DSP R VENDU TRÈS RARE! Préampli processeur exceptionnel en HC et, fait beaucoup plus rare. Chord dsp r preamp / surround controller, boxed. CHORD DSP R preamp/ surround controller. with dts and dolby 2 surround. Introduction The Chord DSP forms the centre of a High -End cinema and audio system. The DSP decodes Dolby Digital, DTS and DTS-ES and has the.

Author: Sat Shami
Country: Qatar
Language: English (Spanish)
Genre: Science
Published (Last): 10 January 2017
Pages: 284
PDF File Size: 6.87 Mb
ePub File Size: 7.88 Mb
ISBN: 935-2-31399-325-3
Downloads: 15449
Price: Free* [*Free Regsitration Required]
Uploader: Mazujar

Exit On Screen Display Level setup Allows dps8000r to adjust the relative levels from each of your speakers. Manufactured under license from Digital Theatre Systems, Inc. You can choose feet or meters. Edit the name of your source device? The setting will be overridden if you use a Preset setting for an input. Please consult your dealer with regards to the optimum speaker placement for your system. Chorx This setting allows you to determine how OSD appears. Place the microphone on the listening position pointing towards the roof.

Otherwise these trigger outputs may be damaged. The remote control main menu screen is shown in the diagram below. Surround This setting allows you to control the level of the surround speaker for the selected preset. If the knob is pressed whilst in the cchord interface menus then you dsp8000e enter the selected sub menu.

The audio can be delayed by up to ms up to a sample rate of 48kHz and 0 — 70ms at up to 96kHz in single millisecond steps. This means that the DSP will automatically check for incoming digital audio signals, composite video signals and S- Video signals. Press this LCD touch pad to decrease the value of a selected parameter within the set up menu.

  KUTCHMITRA EPAPER PDF

DSP 8000 AV Processor

Do not connect grounded test equipment. This takes a few minutes to complete. Circuit designs that embody these components conform to applicable safety requirements. Plug the female end socket of the mains cable into the power connector of the DSPand the chlrd end plug of the mains cable into mains wall socket or mains extension socket.

MODE This button is used to cycle through the available post processing modes. Treble This setting allows you to control the level of the treble for the selected preset. See the tape monitor section of this manual for more information.

Used chord dsp for Sale |

Movie soundtracks can sometimes sound quite bright because they have been mixed to suit the acoustics of cinemas. MIC This input is used to connect a microphone. The preset set -up defines the parameters of each preset and allows control over the following levels: The DSP will cycle through each loudspeaker every two second unless you make an adjustment to the level settings Use csp8000r cursor up?

This processing mode offers a natural sound with no reverb added. REC Use this record output to connect any video recording equipment that has a composite video input. PL II Width This control allows centre-channel sounds to be positioned between the centre speaker and dsp800r left -right speakers over a range of eight steps. See Preset set-up menu on page This setting overrides the Treble setting in the Tone Setup. This function duplicates the subwoofer information in the signal to the speakers set to both ‘Large’ speakers and the subwoofer.

  KERACUNAN TEMPE BONGKREK PDF

Use the left and right cursor LCD touch pads or front panel buttons to adjust the gain setting so that the signal never clips. There are ds8000r actions that you can choose to cause the trigger. This means that the DSP will automatically search for an active input source and the processor will automatically check for incoming digital audio signals, composite video signals and S- Video signals.

For example if you are connecting a DVD player, make sure that the audio and video connections have the same number. The lock is off when the DSP is powered up. The table below lists all of the actions and describes how they affect the trigger. OSD style This setting is used to change the screen text, background and error message colours.

This menu also includes the subwoofer settings. The display will also light up showing the current settings. The remote control has a backlit LCD touch screen and 8 mechanical buttons. Your processor is connected via a multi-way mains block, which contains an earth point at each socket outlet.

The cursor keys, up?