ASTM F146 PDF

F – 80 Standard Test Methods for Fluid Resistance Of Gasket Materials. Designation: F – Standard Test Methods for. Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the. ASTM F – 04 Fluid Resistance of Gasket Materials This standard is issued under the fixed designation F ; the number immediately following the.

Author: Grojind Garisar
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Life
Published (Last): 18 September 2013
Pages: 47
PDF File Size: 9.70 Mb
ePub File Size: 17.59 Mb
ISBN: 481-2-76592-260-4
Downloads: 74374
Price: Free* [*Free Regsitration Required]
Uploader: Kigaramar

Precision and Bias 7 These test methods are not applicable to the testing of vulcanized rubber, a procedure that is described in Test Method D Link to Active This link will always route to the current Active version of the standard.

Current edition approved April 1, There were six Type 1,7, three Type 3, and one Type 5 material evaluated for immersion weight change and aatm change in IRM oil. Significance and Use 4.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. The specific test fluids and test conditions outlined were selected as typical for purposes of comparing different materials and can be used as a routine test when agreed upon between the purchaser and the manufacturer. Originally approved in It is understood that the results will be reported per D along with the specific immersion conditions used prior to said adhesion test.

BoxTrenton, NJ Please copy and paste this embed script to where you want to embed Embed Script. Pour enough fresh test fluid over the specimens to ensure that the specimens are wetted and covered by the fluid.

  LANSA AS400 TUTORIAL FILETYPE PDF

Dead weight loads are listed in Table 1. The user should be aware that results may differ. After immersing the specimens in the various test adtm, the effect on physical properties astj expressed as change in tensile strength, compressibility in softened condition, flexibility, volume change, and thickness and weight changes from the original condition.

We need your help to maintenance this website. Change the distilled ast used in the test frequently. This gives the final volume, V2. The inch-pound units in parentheses are for information only.

ASTM F 146 – 04

Then awtm the specimens from the cooled-down test fluid and immediately blot the samples with sheets of blotting paper to remove excess liquid from the surfaces.

Use the same sinker throughout. Other physical property tests described in this standard are not applicable for these materials. Measure the weight of the test specimen to the nearest 1 mg 0. The change in weight of the specimens is to be calculated as an expression of percentage change on zstm original weight.

ASTM F – 01 Standard Test Methods for Fluid Resistance of Gasket Materials

We are a non-profit group that run this website to share documents. It is designed for testing specimens cut from gasketing materials or from finished articles of commerce. Summary of Test Methods 3. Use enough fluid to provide a minimum zstm 10 mL for each specimen in the container. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

The specific test fluids asttm test conditions outlined were selected as typical for purposes of comparing different materials and can be used as a routine test when agreed upon between the purchaser and the manufacturer.

  FOSTEX FX120 PDF

ASTM F – 80 Standard Test Methods for Fluid Resistance Of Gasket Materials

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. These test methods are not applicable to the testing of vulcanized rubber, a procedure that is described in Test Method D The results of these test methods are not intended to give any direct correlation with service conditions in view of the wide variations f14 temperature and special uses encountered in gasket applications. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

F1146 test methods are applicable to ethylene glycol, propylene glycol, commercial coolants and blends with water thereof see Note 1water, and other commercial oils and fuels.

Exercise care when removing the excess fluid so that no squeezing action occurs on the sample. The producer must be aware that different coolant mixtures may yield different results. Thank you for interesting in our services.

Refer to Test Method D for further information regarding immersion test fluids. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Type 1 Class 2—A BA material, containing a normally lower swelling polymer. The anvil shall have a diameter not less than that of the presser foot, which has a diameter of 6.