ASTM E165-02 PDF

Buy ASTM E PRACTICE FOR LIQUID PENETRANT EXAMINATION FOR GENERAL INDUSTRY from SAI Global. ASTM E Standard Practice for Liquid Penetrant E Standard Practice for Liquid Penetrant Examination for General Industry View on Information. Find the most up-to-date version of ASTM E at Engineering

Author: Mim Fegal
Country: Cameroon
Language: English (Spanish)
Genre: Environment
Published (Last): 19 September 2010
Pages: 481
PDF File Size: 4.76 Mb
ePub File Size: 2.33 Mb
ISBN: 658-1-86904-442-5
Downloads: 2171
Price: Free* [*Free Regsitration Required]
Uploader: Nehn

Active view current version of standard. Non-destructive examination NDE is used to detect cracks and other flaws in a part without rendering the part unusable by performing destructive testing. It is a common misconception to label a discontinuity as a ashm.

The penetrant that is trapped in any discontinuities will glow when viewed under a black light. A scratch or a pore can easily be misinterpreted as a crack or flaw, and this can lead to unnecessary and costly repairs.

Agreement by the user and the supplier regarding specific techniques is strongly recommended. Advertisement 4 Atm to Page 1 2 3 4 Edit Story. E1650-2 most cases, the discontinuities are visible to the naked eye without liquid penetrant testing. This might involve sandblasting, wire brushing, etc.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Energy-Tech Magazine Contact us.

ASTM E165(02) Espaol.pdf

Non-destructive examination basics Patrick J. Care must be taken not to overly clean and remove the penetrant from the discontinuities. The liquid penetrant examination just makes the discontinuities easier to see.

Then the surface must be allowed to dry. The developer brings the penetrating oil out of the discontinuities by a blotting action. With this technique, liquid penetrant is applied to the surface of a material and is drawn into surface discontinuities such as cracks, pits and seams by capillary action.


Pre-clean the surfaces to be inspected. This method substitutes fluorescent penetrating oil for the visible dye penetrant. Cracks typically show up as red lines and pits usually look like red dots. An example of a gear tooth crack that was made more visible using a dye penetrant examination is shown in Figure 1.

Some of the most popular NDE methods include: Work Item s – proposed revisions of this standard.

Liquid penetrant testing Liquid penetrant inspection is the most popular method to check for surface cracks because it is simple and no special equipment is required. They are nondestructive testing methods for detecting discontinuities that are open to the surface such as cracks, seams, laps, cold shuts, laminations, through leaks, or lack of fusion and are applicable to in-process, final, and maintenance examination. They can be effectively used in the qstm of nonporous, metallic materials, both ferrous and nonferrous, and of nonmetallic materials such as glazed or fully densified ceramics, certain nonporous plastics, and glass.

A suitable waiting time allows the penetrant to enter the surface discontinuities, and then excess penetrant can be asttm. These inspections can increase the reliability of the part by asrm early detection of flaws that could lead to a failure.

Box Dubuque, IA Phone: SI units are provided for information only. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Another technique involves the use of an ultraviolet light to view the surface discontinuities. This is typically done with a special cleaning solvent. As soon as the material is dry, the developer is applied. The reason is that some potable water sources contain chlorine, which can leave a residue on the surface and can lead to cracking in some stainless steels.


Astj technique can be qstm on a variety of ferrous and non-ferrous materials, including steel, stainless steel, aluminum, bronze, tungsten carbide, ceramics and plastics. Astn to Active This link will always route to the current Active version of the standard. It should be pointed out, however, that after indications have been produced, they must be interpreted or classified and then evaluated. The surface then needs to be solvent cleaned to remove any greases or oils.

After application of the developer, the visual inspection is done with a black light. The correct term for a discontinuity is an indication, which is not necessarily a crack or a flaw. The purpose of this article is to describe these basic NDE techniques and discuss some of the advantages and disadvantages of the different methods.

The visible dye penetrant technique involves the following steps: Some equipment manufacturers allow some surface indications, depending on their size and location on a particular part.

This can take minutes after the developer is applied. The visible dye penetrant technique involves the following steps:. Also, there are no universal acceptance criteria on the maximum allowable size of an indication.

Dye Penetrant Testing

For this purpose there must be a separate code or specification or a specific agreement to define the type, size, location, and direction of indications considered acceptable, and those considered unacceptable.

The part then needs to be cleaned to remove the penetrant and the developer. To avoid this, any indications should be investigated by polishing and re-evaluating the indication. One of the most critical aspects of liquid penetrant testing is interpreting and evaluating the discontinuities.