L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked[1] _机械 /仪表_工程科技_专业资料。ASTM A Standard.

Author: Kagalmaran Faukasa
Country: Ethiopia
Language: English (Spanish)
Genre: Career
Published (Last): 20 February 2015
Pages: 469
PDF File Size: 14.92 Mb
ePub File Size: 7.49 Mb
ISBN: 309-5-82183-295-8
Downloads: 75486
Price: Free* [*Free Regsitration Required]
Uploader: Dougis

ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

The values given in parentheses are for information only. D PSS means plate, strip, sheet.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The choice of test method for materials in conditions other than annealed wstm be at the option of the seller.

This standard has been approved for use by agencies of the Department of Defense. The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test. This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions. Last previous edition approved in as A — Hard Elongation in 2 in. A number in parentheses indicates the year of last reapproval. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. They shall be formed in different shapes such as sheets, strips, plates and flat bars. Only annealed conditions of grades speci?


The noncontrolling factor normally will exceed considerably the speci? This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? A — 03 Standard Speci? Rockwell B 95 95 Originally approved in Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. An alternative method of determining?

ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

The values obtained in this manner should not, however, be taken as the actual yield strength for 0. C Annealed material that naturally meets mechanical properties may be applied. Current edition approved Oct. ICS Number Code HardC Elongation in 2 in. Asm shall be bent around a diameter equal to the product of the bend factor times the speci?

Material Test Report and Certi? A superscript epsilon e indicates an editorial atm since the last revision or reapproval. Link to Active This link will always route to the current Active version of the standard.

The steels shall adhere to specified chemical composition requirements. Number of Tests 8. This revision of Speci? One bend test shall be made from one end of each coil.


ASTM A Standard Specification for Annealed or Cold-Worked[1]_百度文库

Historical Version s – view previous versions of standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

B Maximum unless otherwise indicated. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM asrm the above address or at phonefaxor service astm. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for aztm Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

This abstract is a brief summary of the referenced standard. Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined. In case of dispute, the offset method of determining yield strength shall be used.