ARITECH CD72 PDF

Thank you for choosing an ARITECH security system. This manual explains how to use the ARITECH CD72 and CD95 series for every day use. There is a. A dual com polls to the monitoring station. What this means is every couple of minutes (depending on what it is set up for) it sends a signal to the monitoring. Hello, I want to integrate a solution based on PLUGWISE and an Aritech Alarm Central. I could successful connect a printer SERIAL RS

Author: Groll Bragal
Country: Brazil
Language: English (Spanish)
Genre: Marketing
Published (Last): 5 December 2010
Pages: 326
PDF File Size: 16.68 Mb
ePub File Size: 4.85 Mb
ISBN: 985-4-73758-840-8
Downloads: 58294
Price: Free* [*Free Regsitration Required]
Uploader: Gobei

If there is a short circuit in the 12 volt power supply, the voltage regulators in the supply together with the fuses will prevent serious damage to the system The 12 volt power supply will decrease sharply in the event of a short circuit. Any zones that may be open will initiate a full alarm condition and the sounders will activate. The zone has two end-loop aritceh 4.

Connection of a fire detector Advisor cd95Advisor cd Find More Posts by mick Mains switching relays must NOT be fitted inside the control panel cabinet. English als bijlage per email. Stel uw vraag in het forum. Maintain a good separation between low voltage and mains supply cables, and use separate points of entry into the control panel cabinet.

Qritech zones should be closed with an end-loop resistor 4. Use of an extra power supply Everybody involved in installing or maintaining this panel should have access to a copy of this manual. The software version is displayed on the aritdch keypads if present. Connection of a relay or an LED on the output Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de aritecu groter is dan toegestaan bij uw provider.

  BUDIDAYA KACANG KORO PDF

For most LEDs, however, a current of approximately 15 mA is sufficient. If there are several detectors place them in parallel and cable the zones as described in figure 1 or 2 see page 8. Ensure that there is a good earth for the alarm system.

Both zones should be closed with an end-loop resistor 4. If the tampers must be placed in separate zones, they can be connected according to figure 1 1 end-loop resistor or figure 2 2 zritech resistors see page 8. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Don’t show me this message again.

Do not forget to initialise additional keypads and expanders with the menu: You can also Private Message one of our Community Managers here. De handleiding is 0,16 mb groot.

The arrows move the cursor during entry. Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. The switching of zritech relays may cause electrical interference.

By pressing ‘print’ button you will print only current page.

Aritech Advisor CD72 Installation Manual

Screw to close siren. Do not use a battery to power the system when installing or changing the installation. You can read the announcement and access links to the revised policies here.

In the CD the expanders have priority over the keypads!

  BASHAIR AL KHAIRAT PDF

Avoid cable ducts and cable ways which contain mains power cables. If a short circuit should occur, remove the 12 volt connections one by one. Avoid loops of wire inside the control panel and route cables so they do not lay on top or underneath the printed circuit board.

Please sign up or log in to join the discussion. Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel of niet mee geholpen bent!

Supply only mains power to the control panel. Intended for the manager.

Get out there and share your passion with others! Overview of the dipswitches on Before connecting, the cable between terminal 2 and afitech 10 should be removed!

ARITECH ADVISOR CD72 INSTALLATION MANUAL Pdf Download.

Everybody involved in installing or maintaining this panel should have access to a copy of this manual. Don’t have an account? Comments to this Manuals Your Name.

Show Printable Version Email this Page. Overview of the inputs and outputs on the CD Output no. Enter text from picture: Keypad 1 Remote 2 Remote aritevh Connection of a key switch with LED’s This connection also applied for detectors which require a reset after an alarm, e.

This may not be greater than 40 mA. If aritwch sirens have been activated, these will now stop.