APS997C INSTALLATION MANUAL PDF

Model APSC. Owners 24 Hour Timed Start Setup, Operation, and Use 23 of this manual has a section for the particular features and options installed in. Save this Book to Read prestige apsc installation manual PDF eBook at our Online Library. Get prestige apsc installation manual PDF. AUDIOVOX APSC INSTALLATION MANUAL — | PDF | 73 Pages | KB | 09 AUDIOVOX APSC INSTALLATION MANUAL The key.

Author: Bam Makus
Country: Slovenia
Language: English (Spanish)
Genre: Music
Published (Last): 13 June 2013
Pages: 281
PDF File Size: 19.86 Mb
ePub File Size: 13.95 Mb
ISBN: 288-5-86983-226-9
Downloads: 94778
Price: Free* [*Free Regsitration Required]
Uploader: JoJosho

This wire will show 0 volts when the key is apd997c to the “OFF” Parking Light Flasher Input This wire is the common contact of the on board parking light flasher relay. Understanding the difference between a mechanical and an electrical Neutral Start Switch will allow you to properly identify the circuit and select the correct installa- tion method. Ignition 2 Output Connect this instlalation to the ignition 2 wire from the ignition switch.

Prestige APS-997C Installation Manual

Page 16 These applications require the use of additional components which may include relays, fixed resistors, or for convenience, a Door Lock Interface. Add to my manuals Add. Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay. Avoid mounting components or routing wires near hot surfaces or near moving parts like the steering wheel as it may prevent proper operation of the vehicle. This is accomplished by first mapping out the firing order of the engine in groups of as indicated below.

Monitoring The Vehicle’s Engine: Once activated, the unit will installaion 1 time if the vehicle temperature reaches “0 ” and then will run the allotted time. Be certain that the chosen mounting location will not inhibit any of the controls of the vehicle.

  AGILENT E4403B PDF

PLATINUM APSC INSTALLATION MANUAL Pdf Download.

In this application, the Red wire of the door lock harness provides a ground pulse during the arming sequence, or pulsed ground lock output. The mounting location selected must be within 24″ If the vehicle’s parking lights are ground switched, connect this wire to chassis ground. By pressing ‘print’ button you will print only current page.

To print the manual completely, please, download it. To achieve optimum performance the coil signals must be evenly distributed. When completing an installation using either of the following key in sensor circuits, if the operator inserts the ignition key while the vehicle is running under the control of the Remote Start, the vehicle will shut down. Page 11 ground trigger output wire of motion detectors, microwave detectors, or glass break detectors, can be connected to this Light Green trigger input wire.

Locate the control wire that connects the drivers door pin switch to the key in sensor switch. This is a normally opened starter cut arrangement, when power is removed from the security system, the starter disable feature will remain operational, and the vehicle will not start. Connect the Red wire to the low current ground signal wire from the factory door lock switch to the factory door lock relay.

Cut this wire and connect the ignition cylinder side to chassis ground. Draw a circle around any of the columns. Don’t have an account? Parking Light Flasher Feed This wire is the aps9997c contact of the on board parking light flasher relay. If the vehicle’s parking lights are ground switched, connect this wire to chassis ground.

Programming Remote Start Feature Bank 3. Connector Port The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface aps9997c. The following two circuits may be used only if the above circuit is not available.

  BHAVISHYA PURANA IN KANNADA PDF

Mechanical Neutral Start Switch from starting in gear.

Platinum APS-997C Installation Manual

Ground Output While Running – mA This wire provides a mA ground output that becomes active 3 seconds installatikn the Remote Start Unit initializes and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. For technical support go to www. Don’t show me this message again.

Tachometer Input Signal This wire will continually monitor the engine’s tach rate while the unit is under power of the Remote Start module. This unit has the ability to learn the dome light delay time, up to 60 seconds.

Shock Sensor By Pass: To decrease sensitivity, turn the adjustment screw counter clockwise. Page of 32 Go. In most cases, the Purple wire will need to aos997c connected to only one door switch no matter how many doors the vehicle has as most door lighting circuits are wired in parallel. The transmitters are pre-programmed from the factory, If you find you need to program new or additional transmitters follow the instructions below.

Enter text from picture: Choose a location above the belt line dashboard of the vehicle for best reception. These applications require the use of additional components which may include relays, fixed resistors, or for convenience, a Door Lock Interface.

Temperature Start Programming And Information. Pressing the pre-programmed transmitter button s will access channel four and will remain active, for up to 20 seconds, ijstallation long as the transmitter button s is held.

Sps997c to this Manuals Your Name.