This handbook is designed to be a useful collection of engineering and technical information on electrical and optical wire and cable and related products. Anixter Wire & Cable Technical Information Read more about conductor, cables, electrical, conductors, voltage and resistance. View Anixter Cable from ENG 1 at Tsinghua University. WIRE AND CABLE TECHNICAL INFORMATION HANDBOOK $ HARDBOUND $

Author: Mezizilkree Mehn
Country: Albania
Language: English (Spanish)
Genre: Finance
Published (Last): 6 May 2008
Pages: 333
PDF File Size: 12.47 Mb
ePub File Size: 12.78 Mb
ISBN: 691-1-60109-803-9
Downloads: 7675
Price: Free* [*Free Regsitration Required]
Uploader: Voshakar

Lead alloy sheaths, containing added tin or antimony, are used where a harder sheath is desired or where vibration may be encountered. Steel fire doors provide access to the 2nd and 3rd levels for installing cables, and 1 ft 3 2 ft rectangular holes in both the second and third level floors allow cable to be installed in racks extending between the first and third levels. Multimode, on the other hand, has a core diameter of 50, Documents Flashcards Grammar checker.

There are a number of commercially available nandbook pulling compounds many ajixter which are UL Listed that are suitable for use with polymer jacketed cables. Among the most common are Type W and Type G.

Larger diameter cables or those requiring anixtee tests may necessitate a longer lead. G G — A UL cable type. A voltage higher than normal operating voltage is applied across the insulation. For example, a transmitter, interconnecting cable, and receiver should all have the same impedance. Not applicable in the UL version.

Anixter Wire & Cable Technical Information Handbook

Data and suggestions made in this publication are not to be construed as recommendations to use any product in violation of government law or regulation relating to any material or its use. Telephone cable is usually classified according to its location of use. CD — Carrier Detect. There are a variety of types available.

ComiXology Thousands of Digital Lnformation. An arbitrary test voltage level could break down a cable circuit that would otherwise render long trouble-free service at normal operating AC voltage. Boosting generators are also used to raise the level of a DC line.


Wire and Cable Technical Information Handbook: Anixter: : Books

Designated as the amount of current that flows when one volt of emf is applied across one ohm of resistance. This includes hookup and lead wire, airframe wire, control cable and coax.

Cable reels should only be lifted by forklift trucks from the sides and only if forks are long enough to cradle both flanges. This can be accomplished in a number of ways. Loose buffer is used in outdoor applications and can accommodate the changes in external conditions i.

Generally, the more twists per foot of cable, the better the cable is electrically balanced. CATV — Community antenna television. Their main application is in cost sensitive consumer applications. UL Listing is by contract with each manufacturer. A comparison is shown below: An integrated circuit device that converts analog signals to digital signals. The tight interface of the threads, especially when subjected to vibrations, allows the connector to maintain a low VSWR up to 11 GHz with flexible cable and up to 15 GHz with semirigid cable.

This armor is generally used on shipboard cables because it provides the mechanical protection of an armored cable, yet is much lighter in weight than other types of armored coverings. The three most widely used are Methods 1, 3, and 4. Cable should not be wound closer than approximately 2″ from the outer diameter of the flange.

Virtually all outdoor cables require a breakout kit in order to connectorize the fibers. This type of sheath provides an impervious seal against moisture and other chemicals as well as physical protection. TDRs analyze the reflections and report handbkok amount of impedance mismatch and the location of faults.


Elevator lighting and control cable with thermoplastic insulation, three braids, flame-retardant and moisture-retardant finish. These connectors are typically used for single mode applications but multimode connectors are available. Ampacity equals the 60 Hertz ampacity multiplied by the derating factor.

Lengths are limited due to amount of material in the ram, thickness of the insulation, and preform size. CPE compares favorably with most other currently used synthetic elastomers used for cable jacketing. If more than one cable is involved the caable should be bound together with electrical tape before applying the grip overall.

Considering the substantial amount of cable present on a ship or submarine, a reduction in cable weight will have a considerable impact on the overall load, thus improving performance and increasing efficiency. Remember that insulated conductors are capacitors. Every installation detail cannot be covered here but staying within the above tension limits will help assure a successful installation.

Cable Types and Selection Criteria 59 7.

All data herein are subject to cale without notice. A typical volt control cable is shown below: Category 5 cable has more twists per foot than Category 3 or 4 cables and, therefore, offers better protection from EMI problems. Conductors can also be wrapped with tape of Teflon TFE.

CPE does not support the growth of mold, mildew, or fungus.

Anixter Wire & Cable Technical Information Handbook

Alexa Actionable Analytics for the Web. When terminated in its characteristic impedance, reflections from the end of a line are minimized. Fibers are tecunical multimode or single mode.

The dielectric constant is 2. Balanced mode means that the signal is carried on both conductors, which provides greater noise immunity.