most recent revision of the AAMA and. field testing protocols. AAMA 08,. “Voluntary Specification for Field Testing of. Newly Installed Fenestration. The AAMA (Voluntary Specification for Field Testing of Newly Installed Fenestration Products) is a field-testing guide developed by the American. AAMA Voluntary Specification for field testing of newly installed fenestration products. Includes Air Infiltration and Water Penetration.
|Published (Last):||3 July 2015|
|PDF File Size:||11.7 Mb|
|ePub File Size:||6.59 Mb|
|Price:||Free* [*Free Regsitration Required]|
Fenestration Testing Laboratory was founded in and is an internationally accredited test laboratory for fenestration products and exterior building envelope systems. We provide testing services throughout the United States from our headquarters located in Atlanta, GA. BDG has extensive knowledge of most building systems and specializes in forensic water intrusion investigations. SITC utilizes isolation techniques to assist in identifying the source or sources of the reported water leakage.
Are the edges perfectly horizontal and vertical? It’s important to note that the AAMA test standard also utilizes the ASTM E test method which details specific test set-up and equipment requirements for the water penetration portion of the test, and the ASTM E test method which details test set-up and equipment requirements for the Air Infiltration portion of the test.
BDG utilizes professional testing equipment that is calibrated to each specific testing standard for accurate results. It is primarily used for new construction quality control and assurance purposes. This guide illustrates test procedures to ensure air and moisture penetration is minimized in new window installations. What is the drainage design? Member discount will be reflected after successful login to the Checkout process. The project architect, manager, or owner specifies the amount and locations of the windows to be tested; this happens either early in the project or at three intervals in the case of large projects: For window and door manufacturers, the procedure provides a uniform approach for dealing with different code jurisdictions and specific design pressure for each size of fenestration product opening.
The objective of forensic water spray testing is to identify and track the water migration through the simulation of wind driven rain events.
Normally, if a window fails, the contractor should be prepared for a wider scope of testing. This specification is for quality assurance axma penetration testing only. If you are looking for a reputable second or third-party testing company to perform accurate professional testing, provide concise reports, and help you through the entire process, contact BDG today.
AAMA Water Spray Testing
The specification aaam for quality assurance water penetration testing only. The only problem with the verbiage provided is that it is often inserted in a generic format that does not provide details as to the areas, quantity, and specific 50-208 pressures.
It is up to the contractor to ensure these testing parameters are established. This guideline is for forensic or investigative water spray testing only. Please contact AAMA for assistance, as needed. SITC utilizes the AAMA when conducting forensic water spray testing on windows, doors, 502-8 walls, storefronts, slope glazing systems and exterior walls. This allows us to not only properly test fenestrations on new construction projects, but also pinpoint the cause of any test failures and provide accurate recommendations to achieve successful testing results.
Please read our simple purchasing instructions first to ensure a smooth transaction. The number of tests depends on the size and budget of the project.
It is not recommended to notify anyone of the actual test locations until the testing agency arrives onsite. The Requirement of AAMA accreditation assures the specifier that the laboratory has the staff, training, experience and calibrated equipment ama properly perform field testing.
Water penetration observed when testing windows will be given extra attention for the remainder of the project. Read more about what our customers have to say This field check procedure is only intended to evaluate joints, gaskets and sealant details in the glazing which are designed to remain permanently closed and water tight.
Water leakage uses the same method while spraying the window from outside to observe indoor penetration. This specification establishes the requirements for field test specimens, apparatus, sampling, test procedures and test reports to be used aamz verifying the air infiltration resistance performance and water penetration resistance performance of newly installed fenestration products. Guidelines for the type of equipment to use and test procedures to follow are specified in the AAMA What are FTL’s Qualifications?
See our AAMA page for additional information. Field testing and forensic leak investigation services are provided nationwide.
The AAMA is the proper test method for field testing of storefronts, curtain walls and sloped glazing for air leakage and water penetration resistance performance. Then both air and water leakage in that order are determined using a test chamber of constant pressure.
AAMA | Field Testing Quality Control
The AAMA can be utilized if the project requires investigative testing. Is the window square?
American Architectural Manufacturers Association. The testing procedure outlined in the AAMA The construction contract will appoint a party responsible for the cost of the testing. Professional services based on accurate information that helps you or your company make the right decision regarding your project or asset.
Begin your publication search by entering information into the fields below. A predetermined amount of air leakage is allowable; however, no water leakage is permitted at all.
It has become the gold standard for all water penetration resistance testing conducted in the United States in regards to fenestration products such as windows, doors, and skylights.