2N 2N 2N DESCRIPTION. ·With TO package. ·Excellent safe operating area. ·Complement to type 2N 2N 2N respectively. 2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics. 2N datasheet, 2N circuit, 2N data sheet: MOSPEC – POWER TRANSISTORS(15A,75W),alldatasheet, datasheet, Datasheet search site for.

Author: Teshura Tojagrel
Country: Laos
Language: English (Spanish)
Genre: Education
Published (Last): 19 March 2007
Pages: 359
PDF File Size: 16.24 Mb
ePub File Size: 9.4 Mb
ISBN: 517-7-66802-585-6
Downloads: 36050
Price: Free* [*Free Regsitration Required]
Uploader: Kajit

Returning to the above dataasheet, the full- wave circuit will be considered. Semiconductor Mounting Considerations An area of regulator construction which frequently does not receive proper attention is the mounting of the semiconductor power devices.

To reduce cost, most earlier approaches of using choke input filters, soft start relays Triacs. Diode D 2 protects against capacitor C Ac y from discharging through the regulator during an output short circuit.

Here extra voltage capability may be needed to make up for the imbalances caused by different values dtasheet capacitance and leakage current.

BOCA (BOCA SEMICONDUCTOR CORPORATION) Electronic Components Datasheet –

For a nominal input of Vac, it maintains regulation over an input range of 90 to Vac datasgeet load range of 2: Operation with a load common to a voltage of opposite polarity — In many cases, a regulator powers a load which is not connected to ground but instead is connected to a voltage source of opposite polarity e.

Q12 will inhibit the output until the ac line is disconnected. In the power stage of Figurea single 2N transistor blocks V and switches 1. Construction Input Supply Design: Welcome to the ECE Store. Regulator reverse biased 3. At each peak of the line the output of the comparator discharges the delay capacitor C D.


Daasheet supply must be isolated from the main supply voltage since the MCI “floats” on the datashest voltage.

This manual describes Motorola’s voltage regulator products and provides information on applying these products. Note that the pass element is required to operate with 2m6489 collector current of only Isc during short circuit conditions, not the full output current, Ik.

Power Transistors

In these newer designs, snubber elements are smaller and voltage spikes datashert energy left in the leakage inductance may be a more critical problem depending on how good the coupling is between the primary and clamp windings. Using the circuit in Figure on switching supplies where the filter capacitors are not isolated from the line would defeat the isolation in the switching transformer. F high frequency type capacitor tantalum, ceramic, etc.

The voltage drops in the high current carrying leads now have no effect on the load voltage, Vl. This problem datasbeet be avoided by proper placement and connection of the filter capacitor return load as shown in Figure Gate waveforms will show a step at a point just above the threshold voltage which varies in duration depending on the amount of drive current available.

RMS and Peak repetitive rectifier current ratings can be determined from Figure The flyback converter stands out from the others in its need for a low inductance, high current primary. From Figure we can daasheet that any lead resistance between these points and the load will cause the load voltage, Vl, to vary with datasheeh load current, iL.


The solution is to utilize a different regulator configuration known as the “regulator within a regulator approach.

2N6481 Datasheet, Equivalent, Cross Reference Search

In this latter case, provisions are usually made either internally or by wire “OR”-ing the outputs to convert the dual output to a single output channel. Here devices that would normally be used in switchers from 10 to datasheft are listed next to circuits in which they would generally be used. Switchers also exhibit long hold-up time due to their inherent ability to regulate over wide variations in input voltage.

See Section 3 for circuit techniques.

The control signals are external inputs that can be fed into the dead-time control FigurePin 4the error amplifier inputs pins 1, 2, 15, 16or the feedback input Pin 3.

This means that transformer size is sacrificed for circuit simplicity. If greater output currents are desired, the current boost configuration shown in Figure E can be used. These considerations are given below: With a constant supply voltage, Vcc, and junction temperature, the output voltage is given by: The latest bipolar transistor can operate efficiently up to kHz, and datazheet FET seems destined to own the to kHz range.

Depending on Vin, Ta, heatsinking and package utilized, output currents in excess of mA can be obtained with this configuration.